The device for bending of collars on forging  See details »

 
Video subtitles:
  • 00:01: Hello here I I keep the topic clamps and now showing devices on which I wildebeest clamps but here here triangle me It took 15 centimeters here such finger on the tow 25 millimeters diameter over there such as the round it is also a washer
  • 00:30: cut off from the tow bar of old there too there diameter 25 millimeters there just because he well comes as a and even there own washer Bottom there it will stew that maintained So here it would be Lower costs for hijacking To be mounted on the the grip and that's how squares are brewed here these pieces Steel from springs and they will serve
  • 01:00: stops here on the left for the parties to smooth angle to clamps bend here on the right side there semicircular for round, we do not Only work in stripes or square on the case so often We have to work of logs so there for round
  • 01:49: But if that's brew these with springs here these pieces and stop here no longer need to axis brew bottom lift here in this
  • 02:01: I place here first I picked to well then find out exactly I check and then I I said to sleep must also check it will work in So here it would be brewed axis pen It is already now I have outcome may be brewed and It will have to check as something that's worth Here I am now, too I am stuck on two points and I will check it out as it is not well to simple wire here I show how Now it will work But both want to
  • 02:33: its axis to the left here Right here I have already tack-welded and So I check it just as it bends but everything's ok Now after this I could cook pen and there is more the emphasis here is to Puck He did not fall to So why lever he stands and is such thrust washer on it
  • 03:01: it will move arm it will motionless puck on it yes it will slide like this our must somehow to keep him so three he'll make a point to as if do not cook much but Only three points enough here Now it remains for me weld holder to strengthen the onslaught and can be squared boil on for
  • 03:31: anvil but I I'll make me like work like onsets and more convenient so therefore I have to the clutches of the square I do someone may like to anvil work in our square on Well but here's the fact place I have very thin gusset and I had could already be there a fat metal underlay because I do not now I will strengthened I'm such backing Now under it and
  • 04:01: Weld them and there is place there will be stronger that was stronger our there are sulfur heavy loads all here they told me Privalov and now This place metal the crowd and it will has tightened the I now place it I will experience different strips will bending metal different thickness and different
  • 04:30: width and can be see that's how he I work here three I will stick to and even four will bend I check posted It is normally days forum
  • 05:18: in general, the machine bends ok well the oppression but this pen which the department beginning but she is from I've done dozens of square just their Now I put together
  • 05:30: I burned and even here welded on I grab it and welded to it here riding and she It was weak and because there is still heavy loads and people over there at the end of I would have seen me then replaced because I tried four band and very wide when she tried I start to bend well everyone else that's out there All ok and this is now on handle
  • 06:00: Start bend us because soft metal forging It was not enough for him overall width should be there wide good handle cook but there at the end I am now to be seen brew already there normal pen by springs and I will such strips 2, it reinforced handle will after that stop it no longer will no longer be in my generally from the right side of me there's this emphasis
  • 06:31: rounded on him You can circle round rounded to the place for logs say now I'm there too I will show here I show here and yet constantly wildebeest you were here to clear how the adaptation
  • 07:14: name
  • 07:30: Now here I I show it here rounding the corner where let's say if a direct angle almost getting we did not clearly visible on Rounding here that's how I enclose to 90 degree bend because there is a gap most between the anvil and here gons device here so when enclose smooth lesson receive 90 degrees, you see rounded round this place for round forgings for round parts
  • 08:01: Now let's say two angles if I need yoke will seal round blanks roundwood in general here those parties that side for conventional but squares and everything else there band any more bands what is going to be there
  • 08:34: but he did the prophet oppression good package it narrow here is a prophet Thursday's is Round the corner was, and that's Here's witty a wee bit
  • 09:04: here copper Four point here strip it even slightly thicker and yet close at all widespread here I how I caught here This is shown by the arrow place start to bend all means this pen do not go here not it is difficult to change the same gland I cut corners I cleaned and everything that's it this handle on it gently not go out
  • 09:31: or a stronger metal wider and thicker strip need to be here but I here and so did I here I flunked the bottom wider and on top there already a little but all of the springs and so there's see from prihvachen already there is a great reserve the pen is not we will bend weaknesses in place it was there bending the soft metal it suits me here this is I had already checked themselves to normal work why such but this device
  • 10:00: device is not It is like to a benchmark that's it It is to do here such as here with this here I will not stay him before He showed not from role on my channel here Now even this one pusher as he There's even a video it is even better for this so well here if him to do clamps to bend his it is necessary to close the roller so a round shaft great and this one Now a wave there one the fourth part just need to remove it on it can also be bend clamps It is still possible differently in general
  • 10:30: can come up still be somehow easier you can do but these stanochke these ones tools they they have already checked They work really all while and see