Eduard Izmaylov

Saved 9/20/16 5:27 AM from repair

Jammed the sharovy crane how to block?  See details »



Video subtitles:
  • 00:00: Hello. In this video, I'll tell you what to do if the ball valve is not blocked. Many people do not know that the ball valve is necessary at least once a month to turn. A complete cycle of 90 ° in one direction, to the end of its block. And 90 ° to the other. Parallel pen tap - tap is open. Perpendicular faucet handle - the valve is closed. Here is a simple operation to open and close the valve will extend the service life of the crane. If you do not, then after about 5-7 years on the cold water faucet is overgrown with stalactites and the ball just stuck. It is not possible to block.
  • 00:34: If you are faced with a similar situation and you tap do not overlap, but now I will show, you can try to block your ball valve. I try to block it, and it does not overlap. Here comes up here and all. There are times when he did not move. Though you what to do, he does not go there. Many people simply take the pliers and try to turn it with pliers. Unfortunately, this almost always ends with the butterfly breaks off. So I do not recommend any of pliers does not take up the pen.
  • 01:06: Because the handle is made of silumin either or aluminum. Both breaks at once - twice. What should be done? Unscrew the nut and remove the butterfly. Butterfly removed. Some cranes have just such a clamping nut. This nut is pressed against the gland. If the stock does not move, the ASSUME this gland and unscrew a little bit. It needs to be a little release. Slightly unscrewed. Twist the whole it does not need. After a little bit when you let go vtoroplastovaya gasket vtoroplastovy
  • 01:38: the gland, which is located there, a little decompressed. And then you need to take some appropriate key and get here for this stock. It is for these faces. And a pair of pliers can be a last resort, but a pair of pliers, you can crush the stem. And so that's a little bit. Ras opened. Two. Three four. In this case, you will not need to rush. Each time a little bit. Opened. Closed-opened. Closed-opened. Each time the amplitude increase, and increase.
  • 02:11: If you take and immediately fell swoop key here and so open, those. override, then you break the ball. You break a screwdriver or a ball. At the end of the rod inside the faucet is a screwdriver, which is put into the groove on the ball. And after that you just take and turn sharply, then breaks or crumbles the ball itself, or broken stem. Both lead to the fact that the crane in any case will have to change.
  • 02:41: Attempting to close the valve stroke. See pen goes, the ball is stationary. Here's our ball valve. Here I had to understand. And here is the trash. Please, gentlemen. The ball just split. This is his leftovers. In most cases, if there is such a crane, or amplified in a thick body
  • 03:11: operation, which is now showing, tap and revives it for a long time and regularly going to work. And then a little bit back and forth, back and forth. How long it may take? It all depends on the degree of crane jamming. It may take you 10 minutes. More than 10 minutes, I have not encountered. I still do not engage in such an operation. As you can see a drop of water came out. Nothing wrong. It's just unclenched stock. After that, I tighten the nuts and vtoroplastovaya prokladochka It shrinks back and everything will be through. Here and there a little bit.
  • 03:41: Little by little. Little by little. All. My ball valve closed. Now, in order to make sure that it is covered at 100%, I take the butterfly put back. And I look into the groove. Now I look to this part of the butterfly touches here to this part of the ball valve. Until it stops. This is called stress. I have not concerned, so I rasshevelivayu tap on. Everything came to stop.
  • 04:12: Tepeo I should tighten the nut. Caul times. And two. After all this, to wipe dry paper towel or toilet paper that is at hand and check whether there is a leak after when he was pulled up the gland. All dry. After that dress pen. I tighten the screws.
  • 04:43: Better tighten the nut and to the end, to the butterfly pressed all the way down. That it touches the stops on opening and closing. If your tap is not omentum, this Gadget, as I said, that without Gadget, perform exactly the same operation. If it came out, then, unfortunately, it will be necessary to change the valve. But the ball valve flow only in a variable position - like that can flow from the omentum. If it is fully open or fully closed,
  • 05:14: it will not leak. You see, I revived the crane. He moves well except that at the end a little bit goes tugovato. A little more of his work out here and there and the crane will continue to live. As you can see the operation is not very complicated and the operation handle almost any person. The only thing I must warn you, if you have a reinforced valve valve body fat, as in my case, then you can easily try, what I have just recommended.
  • 05:44: If the valve body looks very thin and suspicious, it is better not prodelyvat this operation. Why? Because the valve body can break down. But he can not break because the crane thin. Often valves are made of thin steel correct, and sometimes delicate valves that are made do not understand anything else. Type silumin or as he also called. Such cranes schelbany let it crumble. Therefore, such an operation so it is better not prodelyvat cranes. So, if a thick cock, do. If a thin crane, please, close the water somewhere to tap and change without attempts to recover it. If this stoyakovy tap, you will have to call the housing office and ask them to either blocked riser
  • 06:21: or you came and changed the valve. I hope my user guide will help many people who jammed ball valves. That's all. Artem was with you. Till.